This is a TCI 55w 1050mA MaxiJolly Dali dimmable constant current LED driver. The full features list is as follows:
•Multipower driver supplied with dip-switch for the selectionof the output current.•IP20 independent driver, for indoor use(DC MAXI JOLLY HC/2 DALI).•Class I protection against electric shock for direct or indirectcontact (DC MAXI JOLLY HC/2 DALI).•Driver for built-in use (DC MAXI JOLLY HC DALI BI).•It can be used for lighting equipment in protection class I.•Active Power Factor Corrector.•Analogical input (NTC) for thermal sensor connection.•Auxiliary output 12 V max. 100 mA.•Current regulation ±5 % including temperature variations.•Input and output terminal blocks on the same side(wire cross-section up to 1,5 - 2,5 mm2/ AWG15 - AWG13).•Clamping screws on primary and secondary circuits for cableswith diameter: min. 3 mm - max. 8 mm (DC MAXI JOLLY HC/2DALI).•Protections:- against overheating and short circuits;- against mains voltage spikes;- against overloads.•Thermal protection = C.5.a.
Operation mode:
Operation Mode•Light regulation 0/0,5 - 100 % by means of PUSH function, 0/1...10 V interface(I=1 mA) or 100 Kohm potentiometer and DALI.•Features DALI dimming:- memory function for sets or light groups;- recall of stored functions;- compatible with standard DALI interfaces.•Light regulation 0/0,5 - 100 % by means of PUSH function (mains voltage):- a short push to turn on and off;- a longer push to increase or decrease light intensity;- regulation automatically stops at minimum and maximum values;- for another on, regulation or off command, release the push button and givethe desired command again.- dimming level memory at mains restore.•Possibility to use PUSH function to 4/5 drivers without sync cable.•Maximum length of the cable, from push button to last driver, must bemax. 15 m / 49 ft. In case of applications where the cable is longer than15 m / 49 ft, keep this separate from the 110 - 240 Volt mains cable.•ATTENTION: only use normally open push buttons with no incorporatedwarning light.•Specific dimming terminal connection with a 0/1...10 Vdc electronicpotentiometer (0/1…10 V local dimming, double insulation required forexternal connection).•Max. 10 synchronised drivers of which only one can be controlled(1 Master + 9 Slaves).•Synchronization cable is separately supplied.
TCI BCC/SL - Linear mini electronic ballast 1x 10W
Product Code: BCC 116 SL*
T5 4-6-8-13-14W
T8 16W
PLS 5/7/9/11W
PLC 10W
2D 10-16W
DATA SHEET
Description- Compact size electronic ballast for built-in use - Suitable for connection to emergency equipment in compliance with EN-60598-2-22 - Can be used for lighting equipment in protection Class l and ll - Push in connector with retaining springs. Connector cross section 0.5 - 1.5 mm2 - Start with pre-heating for longer lamp life (cut-off function) - Protection against lamp disconnection (re-start with pre-heating), lamp failure or end of life - Ballast can be secured with slots for M4 screws
Specification
Lamp
TC-D/E
Cap
G24q-1
Power (W)
10
Length (mm)
150
Width (mm)
22
Height (mm)
19
TCI BCC122 is a non-dimmable ballast to run: 1 x 28 Watt 2D compact fluorescent lamp OR 1 x 21 Watt 2D compact fluorescent lamp OR 1x22w T5 Circular
Width: 41mm Height: 18mm Length: 80mm
The TCI DC MAXI JOLLY US DALI LED Driver offers versatile multipower output adjustable via dip-switch for precise current selection. Designed for indoor use with IP20 rating, it features Class II protection against electric shock for both direct and indirect contact. Suitable for built-in applications and compatible with lighting equipment of protection classes I and II, it includes an active power factor corrector and an analog input for thermal sensor connection. The driver provides a 12 V auxiliary output (max 100 mA) and maintains current regulation within ±5%, accounting for temperature changes.
Input and output terminals are conveniently located on the same side, supporting cables up to 2.5 mm².
Robust clamping screws accommodate cable diameters from 3 to 8 mm. Comprehensive protections guard against overheating, short circuits, voltage spikes, and overloads, with thermal protection rated C.5.a.
137968/155 MBQ 155/2
This ballast will operate the following lamps correctly:-
1 X 2D 55W 4-Pin
1 X 55W T5 Circular
1 X 60W T5 Circular
Descriptions
Value
Voltage
220-240
Length
103mm
Width
67mm
Height
21mm
Fixing Centres
93.5mm
Powerfactor
.97
IP Rating
20
Manufacturers Part Number
137968/155
PDF
This driver covers nearly all non dimmable constant current options up to 1050MA
Dimming: NOT DIMMABLE
Additional technical features: RIPPLE FREE, ACTIVE PFC (pf>0.9), SELV <>
Approvals: KEMAKEUR, ENEC, CCC, RCM, CE, EAC, UKCA,
Plastic case: IP 20 (Independent Use)
Minimum cut-out hole diameter: 50 mm
Size: 146 x 22 x 43 mm
Product Information Download
