3 hour DALI-2 self-test emergency lighting conversion kit, designed to suit an extremely wide range of LED types and circuits. The D2N/1 and D2N/1S/80 automatically adjust the output LED current to provide the best match between the battery and the load, providing maximum illumination whilst ensuring full battery duration. The D2N/1 will operate LED loads between 6-55V forward and the D2N/1S/80 will operate LED loads between 6 and 80V forward. Suitable to operate with the LiteMesh wireless system.
net-19-33-17
This product is fully DALI-2 compliant and in keeping with the DALI-2 Standard, if the module is commissioned without a DALI control system present, the unit will revert to standalone self-test, indicating its faults via the charge LED.
The D2N range has been independently certified by TÜV to ensure that the product, has been tested for safety and that it complies with the requirements of national and international regulations.
D2N/1 DALI-2 Addressable Conversion
Specifications
DiiA Registered DALI-2 Device
2-pole Changeover Relay
Additional 3rd Pole Relay for Driver Protection
Deep Discharge Protection
Intelligent, Low Energy, Charging Circuit
Extra Long Life LiFePO4 Cells
Slim Module for Integral Mounting
D2N/1 – Average Emergency Output of 2.2W
D2N/1S – Average Emergency Output of 2.6W
Can Operate with the LiteMesh Wireless System
TÜV Tested and Certified
LiFePO4 Automatic Battery Protection and Recovery
D2N/1D2N/1S/80
LED Voltage Range
6-55V6-80V
I Rated
352mA – 40mA410mA – 33mA
P Rated
2.2W2.6W
LED Voltage Limit
55V80V
Battery Discharge Current
950mA1.1A
Mains Supply
230-240V AC 50/60Hz
Power Rating
1.4W 12mA λ = 0.48
Charge Current
225mA nominal
Recharge Period
24-hours
Battery Pack
3.2V 3.8Ah LiFePO43.2V 4.8Ah LiFePO4
Battery Cut Off
2.5V
Ambient Temperature (Ta)
Module and Battery 5-35°C
Case Temperature (Tc)
Battery 5-55°C, Module 5-70°C
Integral Kit Size
Module – 178mm x 30mm x 22.5mm FC=172mm /1 Battery – 90mm 28mm Ø /1S Battery – 230mm x 24mm x 21mm
Order Codes
Order Code
Description
D2N/1-K
Module, single cell battery and charge LED indicator for LED loads from 6-55Vf
D2N/1S/80-K
Module, three cell battery and charge LED indicator for LED loads from 6-80Vf
The S/ADM/1 DALI-2 Self-Test range is supplied with a choice of LED emitters and is designed for ceiling recess applications. The maintained/non-maintained emergency driver is supplied with strain relief cables and passes through a 40m to 43mm aperture
The Liteplan S/ADM/1 Ceiling Recessed DALI Addressable is a 3 hour 700mA self-test emergency driver with plug and play capability, designed for constant current LED devices. It comes with extra long life LiFePO4 battery packs and is suitable for recessing into the ceiling void. This unit is compatible with the DALI standard and can also operate with the LiteMesh wireless system.
Liteplan no longer make this item , however we have a supplier whom can still supply them to the same spec but wont have a Liteplan label on them
https://www.liteplan.com/images/products/Batteries/NiCd/3-CD45-PT-AS.pdf
The CBP is a changeover relay unit configured to allow a luminaire to be operated normally from the switched lighting supply and also when the local 240V un-switched supply fails. The changeover then draws power from the emergency supply. This can be 50V, 100V or 240V DC central battery systems or 240V AC static inverter systems. The associated control gear/lamp must be capable of being powered by both 240V AC and the voltage of the central battery being used. upon (un-switched) main failure, the main changeover relay de-energises, and the unit changes over to an intermediate state approximately 0.5s. after this period the emergency supply hold of relay also de-energises and connects emergency supply to the load. Upon restoration of the un-switched supply, the emergency supply hold off relay energises and breaks the emergency supply to the load. Again, after the 0.5s delay the main changeover. relay energises, and connects the switched lighting supply to load. The unit fitted with a dimming inhibit relay, which can be used with dimming control gear to reset dimming level to 100% during the emergency situation. The module is suitable for use with LED, fluorescent and conventional control gear.
CBP Changeover Relay
Specifications
Low Profile Compact Enclosure
Dimming Inhibit Relay
Suitable for both Fluorescent and LED loads
Operates with 50V, 110V and 240V DC Central Battery Systems
The Associated Driver must be suitable for Central Battery Voltage
Available with Strain Relief Cables for Remote Applications
Operates with 240V AC 50/60Hz Static Inverter Systems
CBP
Input Voltage
230-240 Volts AC – 50/60Hz
Power Rating Maintained
2.0W 14mA λ = 0.58
Changeover Relay Rating
3A 240V
Ambient Temperature
5°C to 50°C
Tc Point
Top Centre of case
Tc Max Module
70°C
Module Dimensions
178mm x 30mm x 22.5mm
Module Fixing Centres
175mm
Overall Weight
0.11kg
