Product description
High-temperature NiCd battery pack for use with emergency lighting units
4 year design life
1 year guarantee from delivery date
Properties
Constant high-temperature operation
Temperature depending on the used emergency lighting unit (refer to respective emergency control gear data sheet)
Good charging properties at high temperature
High energy maintenance of the charged battery
Certified quality manufacturer
Casing material made of polycarbonate
1.0 m integrated double-insulated cable
1.0 mm² solid wire, pre-stripped
Suitable for emergency lighting equipment as per IEC 60598-2-22
Driver LCA 150W 24V one4all SC PRE
premium series 24 V – dimmable (IP20)
With strain-relief
Product description
NEW: lumDATA (Luminaire data, Energy reporting and Diagnostics & Maintenance)
Dimmable 24 V constant voltage LED driver for flexible constant voltage strips
Can bei either used built-in or independent with clip-on strain-relief (see data sheet chapter: 1. Standards)
One4all interface and ready2mains enable different dimming options
Dimming range 1 to 100 %
No additional external dimmer is needed
Suitable for emergency escape lighting systems acc. to EN 50172
Nominal lifetime up to 50,000 h
5 years guarantee
Typical applications
Cove lighting, facade accent lighting, ceiling integration
Technical details
24 V, 150 W
Small design (325 x 43 x 30 mm) with stretched-compact strain relief
Small cross section
Push terminals for simple wiring
Output terminals (+/–) equipped twice for more flexibility in the application
Interfaces
one4all (DALI DT 6, DSI, switchDIM, corridorFUNCTION)
ready2mains (configuration and dimming via mains)
Terminal blocks: 45° push terminals
System solution
Tridonic LLE-FLEX ADV 600, 1,200, 1,800 lm/m
Tridonic LLE-FLEX EXC 600, 1,200, 1,800, 2,500 lm/m
In connection with Flex accessories wire to PCB plug
The functioning of third party light sources at a low dim level cannot be guaranteed and is not recommended
Product Details
Status Indication Green LED complete with lead designed specifically for the purpose of indicating when a charging current is flowing into the battery.
· Indicates that charging current is flowing into the battery
· Wire length: 750mm
· Bare Wire Connection
Technical Specifications
Single LED
Colour
Green
25w 350-1050Ma flexC Sr EXC LED Driver - Tridonic - 28000700
Driver LC 25W 350–1050mA flexC SR EXC
excite series
Product description
Independent constant current LED Driver
Adjustable output current between 350 and 1,050 mA via ready2mains Programmer or I-SELECT 2 plugs
Max. output power 25 W
Up to 86 % efficiency
Nominal lifetime up to 100,000 h
5 years guarantee
Housing properties
Casing: polycarbonate, white
Type of protection IP20
Strain relief with loop through function
Interfaces
ready2mains (configuration via mains)
Terminal blocks: 0° / 45° push terminals (input / output)
Functions
Adjustable output current in 1-mA-steps (ready2mains, I-SELECT 2)
Protective features (overtemperature, short-circuit, overload, no-load, input voltage range)
Suitable for emergency escape lighting systems acc. to EN 50172
For cable cross-sections up to 2.5 mm²
Benefits
Application-oriented operating window for maximum compatibility
Best energy savings due to high efficiency
Flexible configuration via ready2mains and I-SELECT 2
No tools required for installation
Typical applications
For downlight, spotlight and decorative applications
Product description
Dimmable constant current LED driver (SELV)
Independent driver with strain-relief housing
Extra flat housing for constrained installation conditions (small ceiling cut outs and low ceiling voids)
Dimmable via leading edge and trailing edge phase dimmers
Trailing edge is a benefit in terms of noise compared to leading edge
Dimming range 5 to 100 % (depending on dimmer)
For luminaires with F or M and MM as per EN 60598, VDE 0710 and VDE 0711
Max. output power 14.7 W
Output current 350 mA
Nominal lifetime up to 50,000 h
5 years guarantee (conditions at https://www.tridonic.com/manufacturer-guarantee-conditions)
Driver LC 75W 100–400mA 1-10V lp EXC
Linear drivers
Data sheet
Product description
Constant current LED driver for luminaire installation
Dimmable via 1 ... 10 V interface
Dimming range 10 – 100 % (Depending on load, for details refer to chapter 4.7 Dimming in data sheet.)
For luminaires of protection class I and protection class II
Adjustable output current between 100 and 400 mA via ready2mains Programmer or I-SELECT 2 plugs
Max. output power 75 W
Up to 94 % efficiency
Nominal lifetime up to 100,000 h
5 years guarantee (conditions at www.tridonic.com)
OBSOLETE , IF using DALI dimming the below will suffice
DALI Alternative
If using DSI no alternative available
Tridonic Electronic compact dimming ballast to run 1 x 26-57w TC Compact
The Tridonic PCA 1x26-57 TC ECO xitec II is a high frequency dimmable ballast for use with DALI/DSI/switchDIM interfaces.
Compatible with the following lamps:
1 x 40w T5 Circular Lamp
1 x 26w Double Turn Compact Fluorescent Lamp
1 x 26w Triple Turn Compact Fluorescent Lamp
1 x 40w Long Single Turn Compact Fluorescent Lamp
1 x 40w T5 Circular Fluorescent Lamp
1 x 32w Triple Compact Fluorescent Lamp
1 x 42w Triple Turn Compact Fluorescent Lamp
1 x 57w Triple Turn Compact Fluorescent Lamp
Tridonic part number: 22185120
Product description
NEW: lumDATA (DALI-2 part ext. 251, 252 and 253)
Dimmable built-in constant current LED Driver
Dimming range 1 to 100 %
For luminaires of protection class I and protection class II
Output current adjustable between 900 – 1,750 mA via ready2mains Programmer, I-SELECT 2 plugs or DALI
Max. output power 60 W
Up to 90 % efficiency
Power input on stand-by < 0.2 W
Nominal lifetime up to 100,000 h
5 years guarantee
Housing properties
Casing: polycarbonate, white
Type of protection IP20
Interfaces
one4all (DALI-2 DT 6, DSI, switchDIM, corridorFUNCTION)
ready2mains (configuration and dimming via mains)
Terminal blocks: 45° push terminals
Functions
Adjustable output current in 1-mA-steps (DALI, ready2mains, I-SELECT 2)
Fulfills DALI-2 parts: 251 (Luminaire data), 252 (Energy reporting) and 253 (Diagnostics & Maintenance)
Constant light output function (CLO)
Power-up fading at AC
Configurable via ready2mains
Switch off the Driver with fade2zero
Service monitor to log certain events
Protective features (overtemperature, short-circuit, overload, no-load, input voltage range, reduced surge amplification)
Suitable for emergency escape lighting systems acc. to EN 50172
Benefits
Application-oriented operating window for maximum compatibility
Best energy savings due to low stand-by losses and high efficiency
Flexible configuration via DALI, ready2mains and I-SELECT 2
Reliability proven by lifetime up to 100,000 h and 5 years guarantee
Typical applications
For linear/area lighting in office applications
